If you keep a beard, learning how to line up a beard with a straight razor is the quickest way to make it look neat and properly kept. Clippers and a trimmer get you most of the way there, but a razor gives you the crisp cheek line and clean neck that you get from a good barber. This guide covers where the lines should sit, which razor makes the job easiest, how to stop the lather hiding your line and how to keep both sides even.

Why a shavette is the easiest tool for edges

You can line up a beard with a traditional cut-throat, but a shavette is easier for most people. It takes a replaceable half blade, the head is slim and you can see exactly where the edge meets the skin. That is why most barbers reach for one when they do edges. A wider straight razor blade hides more of the line behind it, which makes it harder to judge where you are.

The Tumbler shavette has a walnut handle and takes our half blades. Bear in mind that a fresh shavette blade is sharper and less forgiving than a stropped straight razor, so use a light touch until you are used to it. If you are deciding between the two types, the shavette vs straight razor guide compares them properly.

Shavettes go out without blades by normal post, but the half blades, like cut-throat razors, are sold to over-18s only in the UK with an ID check on delivery (details on our delivery page).

Trim the beard first

Do the trimming before any razor work. Bring the beard to the length you want with clippers or scissors, then use a trimmer with no guard to mark the outline you are aiming for. The razor is only there to clean up the skin outside that line and sharpen the edge itself.

Marking with a trimmer first matters because it is easy to correct. If you start with the razor and go too far, you have to wait a week or two for the hair to grow back before you can fix it.

Use clear gel or a thin lather

A thick lather is lovely for a full shave, but for edges it covers the line you are trying to follow. You have two good options.

A clear shaving gel lets you see every hair. Apply a thin layer only on the skin you plan to shave and keep it just off the beard.

The other option is a thin lather. Use a little more water than usual so it is slick but almost see-through, and paint it on with the tip of the brush only where you need it. A plain soap such as our unscented shaving soap is a good choice here, because some men find scented soaps sting on freshly shaved skin around the edges. The guide on how to build a lather explains how to adjust the water.

How to line up a beard with a straight razor

Holding the razor for edge work

Use the same grip you would for a normal shave, with your thumb under the shank and two or three fingers on top. Keep the blade at roughly 30 degrees to the skin. For corners and fine detail, use the toe of the blade (the end furthest from your hand), which gives you more control than the middle of the edge. Stretch the skin with your free hand as you go, because a tight surface gives a cleaner line.

The cheek line

Most cheek lines run from the top of the sideburn, near the ear, down to the corner of the moustache. Some men suit a natural curve that follows their own growth, and others prefer a straighter line. Either is fine as long as it is clean and matches on both sides.

Shave the cheek above the line with short downward strokes that stop at the line. Then go back with the toe of the blade and tidy the edge itself with small, careful strokes. Start higher than you think you need. Taking a cheek line lower makes the beard look thinner on top, and it is the mistake people most often regret.

The neckline

The usual guide is two fingers above the Adam's apple. With your head level, lay two fingers flat across your throat just above it. The top edge of your fingers marks the centre of the neckline. From there, the line curves up and back towards the angle of the jaw on each side, ending just behind the earlobe.

Mark it with the trimmer while your head is level, and only then tilt your head back to shave below it. If you mark it with your head tilted back, the skin shifts and the line ends up too high.

A neckline that sits too high, close to the jaw bone, is the most common mistake. It makes a full beard look like a chinstrap from the side. Below the line, shave with the grain, which on the neck may change direction more than once.

The lip and moustache edges

If you want a sharp edge under the lower lip or along the top of the moustache, use the toe of the blade with very short strokes and pull the lip tight with your free hand. These are small areas, so take very little at a time.

Keeping both sides even

Getting the two sides to match is the hardest part. A few habits help a lot.

Use fixed points on your face as guides, such as the earlobe, the corner of the mouth and the finger widths on your neck, and check the same points on both sides. Work in small amounts and switch sides often, rather than finishing one side completely and then trying to copy it.

Step back from the mirror every few minutes and look at your face straight on, in good light from above or in front. A close-up mirror shows you detail, but it is hard to judge the overall shape in one. Taking a quick photo on your phone, face on, can show up a difference you cannot see in the mirror. In general it is better to take off less than you think you need, because a little more can come off the next day if the line still looks uneven.

Aftercare and how often to do it

Rinse with cold water, pat dry and check for any stray hairs you missed. A light, alcohol-free balm helps if the skin feels warm. Most men find that touching up the lines every three or four days keeps them sharp, and those with faster growth may want to do the neck more often.

Change your half blade when it starts to pull rather than waiting for it to feel blunt, because a tired blade is what usually causes rash along the neckline. Rinse and dry the shavette after use and store it somewhere dry. If you also shave your cheeks fully, our guide on how to shave with a straight razor covers the full shave.

Your next step

For beard edges, the Tumbler shavette with a box of 100 half blades will last most men a long time. If you want to add a brush, soap and a stand to keep it all together, you can build your own kit.

The Vault letter

10% off your first order

Join the list for your code and new guides as they go up.